All posts
AFFiNE
Toeverything·Published Nov 13, 2026
Two people in white hard hats and face masks study a floor plan taped to a bare concrete wall, with the rooms outlined in orange

Before You Knock Down That Wall, Find the As-Built Drawings

What changed (Nov 13, 2026): Published a guest post on finding as-built and record drawings before a renovation, covering the Manhattan permit-plan archive, the difference between as-built, record and measured drawings, and when a PDF converts cleanly to editable DXF.

Cover photo: Source

New York nearly threw its building history away. In the early 1970s, the city's Department of Buildings started a pilot to put old permit plans for lower Manhattan on microfilm, and once that was done, the paper was supposed to go. Historians and architects objected. So did the Landmarks Preservation Commission. Then someone checked the film and found it wasn't up to standard anyway. The project got dropped, the rolls went to the Municipal Archives, and renovators still requested them.

A Century of Manhattan, Rolled Up in Tubes

What's in there? Plans for most buildings on 958 blocks south of 34th Street, filed from 1866 (the year the department was created) up to 1978. To get a permit, you had to hand in drawings. That's why a grand elevation by McKim, Mead & White, the New York Life Insurance Building from 1903, sits in the same archive as a plumber's sketch of a toilet at the Manhattan House of Detention.

You'll also find the fire escape drawing for the Washington Place building where the Triangle Shirtwaist fire broke out in 1911. Some sheets are blueprints, some are aniline prints, and a few were drawn by hand on drafting linen. Everything for one lot, every later alteration included, ends up rolled together with the original building plans. Archivists have been unrolling them one by one, and by spring 2021 they'd gotten through close to 30,000. They'll scan one if you ask.

Three Names That Get Mixed Up

On a job site, "the final drawings" can mean three different things, and people mix up the terms all the time:

  • As-built drawings belong to the contractor. As the job goes, somebody on the crew marks each change in red ink right on the construction set. The duct got rerouted? The door moved a foot left? It goes on the sheet.
  • Record drawings come later, from the architect. The architect redraws those red scribbles into a tidy set, which is what the owner gets handed at the end.
  • Measured drawings happen years later, when somebody walks in with a tape measure because a renovation or a historic survey is on the way.

Fun detail: the people who handle risk for architects' insurers would rather everyone say "record." Their reasoning is that the architect is relaying someone else's notes, and no one wants to sign off on a drawing that claims to show exactly what was built.

Why Old Plans Still Earn Their Shelf Space

Let's say you just closed on a 1920s walk-up and you're dreaming about an open kitchen. The engineer will ask three things right away. Which wall is holding up the floor above? Where's the gas line? Is there an old chimney flue under that plaster? A decent set of architectural drawings answers that before lunch. No drawings? Then the crew opens test holes, and you pay for every one of them.

Buyers use old sets to catch alterations nobody pulled a permit for. Restoration teams use them to rebuild a cornice that crumbled off the facade decades ago. Fire inspectors use them too.

A Scan Can Show a Wall, but It Can't Move One

Most old plans you'll get your hands on arrive as scanned PDFs. They're great for looking. Zoom in, eyeball a dimension, print one for the contractor, fine. Open one in CAD software, though, and you'll find one big flat picture with no wall to grab and no line to stretch.

That's where DXF comes in. Autodesk launched the format with the first AutoCAD back in 1982 and published how it works, which is why AutoCAD, LibreCAD, BricsCAD and a long list of other programs open it.

To get from a PDF to something you can edit, a lot of people now use a PDF to DXF converter such as OnlyDoc. It runs in a browser tab, with no CAD plugin and no account. I like converting PDF to DXF online for one practical reason: the laptop in the site trailer and the architect's office machine end up working from the same file.

What Converts Cleanly and What Needs Tracing

First question before you upload: where did this PDF come from? If it came straight out of CAD software, the geometry is still in there as vectors. Lines, arcs, layers and text come back as proper CAD objects. Plenty of buildings designed or renovated since the switch to CAD have record sets in exactly that form, so ask the last architect before you assume you're stuck with paper.

A scanned 1910 blueprint is another story. Those white lines on blue paper are pixels. Software can't work out where a wall's centerline sits on a sheet that's faded and has a coffee ring on it. Somebody's going to trace it in CAD, scan underneath, one wall at a time.

For the vector kind, try a PDF to DXF converter free of charge first and then spot-check a few key dimensions against the original. I wouldn't send anything structural to the engineer without that check.

Conclusion

Somebody may have surveyed your building back in 1924, so look before you pay for it again. Try the city archive, the previous owner's filing cabinet, or the last architect's server. Once you know what kind of drawing turned up, you'll know if it's a quick conversion or a weekend of tracing, and both are nicer than learning about the gas line with a sledgehammer.